Selection Today: General

Showing posts with label General. Show all posts

Friday, February 17, 2012

BestPrice General Tools 524 Precision Trammel Set

Trammels accurately measure and mark distances that are too great for conventional compasses and dividers. Trammels will accurately transfer measurements, scribe arcs and lay out circles. Points can be replaced with pencils, ballpoint pens, crayons or soap- stone sticks for marking various materials.Features: * Free-wheeling thimble for greater precision.* Aluminum knurled body.* Will accurately transfer measurements, scribe arcs, and lay out circles too large for conventional compasses.* Will fit any scale, 1/2" to 1-1/8" wide.* Two scriber points and two pencil points included.* Up to four points can be stored in body.* Steel collet holds replacement leads, scribers and crayons.* Points reverse into body for safety.* Ruler not included in set.* Each trammel measures 4 inches long (from point tip to end) To insert lead, open the collet by the tip and pull the small metal scriber point out, you will find the lead stored in the housing of the handle. Open the housing by unscrewing the handle and removing the black cap inside of the handle. Remove the lead, carefully insert the lead into the head and tighten collet. Used to scribe arcs and circles that are too great for conventional compasses and dividers Attached to a rigid item such as a steel rule or board Points can be replaced with pencils or other marking tools Precision trammel set that fits any scale, 1/2" to 1-1/8" wide Up to four points can be stored in the body

Visit:
http://penobscotff.com/order-now-father-teaching-son-to-ice-skate-on-frozen-lake-photographic-poster-print-24x32/

Thursday, January 26, 2012

Best Buy General Electric GENERAL ELECTRIC WB02X10733 CHARCOAL FILTER

THIS GENERAL ELECTRIC WB02X10733 CHARCOAL FILTER WILL FILTER THE AIR FLOW INTO AND OUT OF THE RANGE HOOD.

A DIRTY INTAKE FILTER WILL CAUSE YOUR MICROWAVE/RANGE HOOD TO BE LESS EFFICIENT. A DIRTY EXHAUST FILTER WILL NOT ONLY CAUSE POOR EFFICIENCY, BUT MAY ALSO ALTER THE TASTE OR SMELL OF YOUR FOOD.

SPECIFICATIONS:

SIZE: APPROXIMATELY 8.75" X 6.25". THIS GENERAL ELECTRIC WB02X10733 CHARCOAL FILTER WILL FILTER THE AIR FLOW INTO AND OUT OF THE RANGE HOOD.

A DIRTY INTAKE FILTER WILL CAUSE YOUR MICROWAVE/RANGE HOOD TO BE LESS EFFICIENT. A DIRTY EXHAUST FILTER WILL NOT ONLY CAUSE POOR EFFICIENCY, BUT MAY ALSO ALTER THE TASTE OR SMELL OF YOUR Works with the following models: General Electric JVM1840CD001, General Electric JVM1840CD002 General Electric JVM1841BD001, General Electric JVM1841BD002, General Electric JVM1841CD001

Visit:
http://volvo-westcott.com/cheap-new-for-hdtv-samsung-sony-dvd-player-hdmi-cable-10-feet

Thursday, January 19, 2012

For Sale General Binding Corporation Products - Plastic Binding Combs, 19 Ring, 5/8

For Sale General Binding Corporation Products - Plastic Binding Combs, 19 Ring, 5/8"x11", Black - Sold as 1

General Binding Corporation Products - Plastic Binding Combs, 19 Ring, 5/8"x11", Black - Sold as 1 BX

Binding combs have 19 rings and are made of rigid PVC plastic. Won't scratch, chip, peel or color. Wide backs extend full length of books to protect page edges. 5/8" combs are designed for 11" sheets.

Sold as 1 BX

Manufacturer: General Binding Corporation

Total percentage of recycled content: 0

Post Consumer Waste: 0

Country of origin: CN

Sold as 1 BX Manufacturer: General Binding Corporation Total percentage of recycled content: 0 Post Consumer Waste: 0 Country of origin: CN

Visit:
http://aamesjobline.com/savings-quiksilver-mens-surfside-casual-shoeolive13-m-us/

Wednesday, December 28, 2011

For Sale Niagara Cutter SMW835 Cobalt Steel End Mill, General Purpose, Uncoated (Bright), 2 Flutes, Square

The Niagara Cutter SMW835 uncoated (bright) cobalt steel metric end mill has two flutes, a 30-degree helix angle, and a square end to machine a wide range of materials. The cobalt steel substrate can be run at faster speeds and stays sharp longer than high-speed steel tools, while offering greater resistance to heat and abrasion. With no coating or surface treatment, the tool features just the base material for use on a broad range of materials. It can provide an economical alternative to higher-priced coatings.

The end mill’s two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The 30-degree helix angle offers general-purpose machining. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The tool’s square end has straight cutting edges that create sharp, unrounded cuts, while the center-cutting design has cutting teeth at the end of the tool that support making pocket cuts, profiling, and slotting. Cutting diameter tolerance conforms to DIN specifications 327 and 1835. The end mill has a Weldon shank.

End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.

Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.

Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool's ability to remove material Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials Square nose end mills (also called square end) create sharp, unrounded cuts Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling

Visit:
http://fren-finance.com/bestseller-carbon-steel-bandsaw-blade-73

Sunday, December 18, 2011

Cheap Champion Cutting Tool 705-68 HSS General Purpose Jobber Twist Drill 118-Degree Steam Oxide, 12-Pack

General Purpose Drilling Surface treated with black oxide finish 118 Degree Point, straight shank Made in the USA Abrasion resistance and improved coolant adherence

Visit:
http://wwwrks.com/for-sale-se-soldering-iron-ul-60-watt-adjustable-temperature110-volt

Friday, December 2, 2011

Order Now Niagara Cutter C330 Carbide End Mill, General Purpose, TiN Coated, 3 Flutes, Square End, 5/64

Order Now Niagara Cutter C330 Carbide End Mill, General Purpose, TiN Coated, 3 Flutes, Square End, 5/64"

The Niagara Cutter C330 TiN-coated carbide square nose end mill has three flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The tool’s square end creates sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The end mill’s three flutes provide better chip-carrying capacity than four flutes and a finer finish than two. They efficiently remove excess material from the cutting area and provide a third cutting edge to create an improved finish that may eliminate the need for a second finishing cut in some applications. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action.

The general-purpose TiN coating combines stability at high temperatures with hardness for wear protection, increasing tool life and performance compared to uncoated end mills. (TiN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. Cutting diameter tolerance is +0.000” to -0.002”. The round shank accommodates a variety of holders.

Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications Square nose end mills (also called square end) create sharp, unrounded cuts Titanium nitride (TiN) is a general-purpose coating that combines high-temperature resistance and increased hardness compared to uncoated end mills Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling

Visit:
http://bestsellers-sites.blogspot.com/2011/12/buy-now-techni-tool-tweezer-carbon.html

Sunday, November 6, 2011

New General Tools 88P Replacement Point

Replacement Point for #88CM and #88 Returns will not be honored on this closeout item

Visit:
http://satpower.net/order-now-storm-kickin-minnow-04-fishing-lures-gizzard-shad-size-4/

Wednesday, November 2, 2011

New Fujifilm FinePix XP10 Digital Camera USB Cable 5' USB Data cable - (8 Pin) - Replacement by General

5 USB Data cable (8 pin) 5' USB Data cable (8 Pin) - Replacement by General Brand

Visit:
http://directline-brazil.com/ordernow-prefilter-for-gp-500750-tetra/